Role of plasma gas flow rate on the microstructural and mechanical aspects of plasma arc welded titanium alloy joints

Authors

  • T. Pragatheswaran Centre for Materials Joining & Research (CEMAJOR), Annamalai University, Annamalai Nagar, Tamil Nadu, India
  • S. Rajakumar Centre for Materials Joining & Research (CEMAJOR), Annamalai University, Annamalai Nagar, Tamil Nadu, India
  • V. Balasubramanian Centre for Materials Joining & Research (CEMAJOR), Annamalai University, Annamalai Nagar, Tamil Nadu, India

Keywords:

Plasma Arc Welding, Titanium Alloy, Microstructure, Defects, Tensile, Hardness

Abstract

In the present investigation, the effect and role of plasma gas flow rate on the formation of microstructure during plasma arc welding of Ti6Al4V titanium alloy were studied using microscopic observation, energy dispersive spectroscopic analysis, tensile tests and microhardness measurements. Plasma gas flow rate influences the arc pressure, arc constriction, and stability. The transformation
of plasma arc from conduction mode to keyhole mode causes severe changes to the microstructural characteristics of the titanium welds. This transformation takes place with slight variations of PGFR. Weld geometries increase with an increase in the PGFR. The microstructural examination shows that there are various phases formed during the variation in PGFR. Fusion zone had acicular α
and widmanstätten α. Mechanical properties (i.e) strength and hardness of the joints increase with an increase in plasma gas flow rate. In the joint welded with 1 L/min, there is the formation of α-case which is an oxygen rich brittle subsurface structure and found detrimental to the ductility of the joints.

Metrics

Metrics Loading ...

References

Balasubramanian, T. S., Balakrishnan, M., Balasubramanian, V., & Muthu Manickam, M. A. (2011). Effect of welding processes on joint characteristics of Ti-6Al-4v alloy. Science and Technology of Welding and Joining, 16(8), 702-708. https://doi.org/10.1179/1362171811 Y.0000000062

Balasundar, I., Raghu, T., &Kashyap, B. P. (2019). Correlation between microstructural features and tensile properties in near-α titanium alloy IMI 834 processed in the α + β regime. Materials Performance and Characterization, 8(5), 932-945. https://doi.org/10.1520/MPC 20180162

Baruah, M., & Bag, S. (2016).Microstructural Influence on Mechanical Properties in Plasma Microwelding of Ti6Al4V Alloy.Journal of Materials Engineering and Performance, 25(11), 4718-4728. https://doi.org/10.1007/ s11665-016-2333-8

Brewer, W. D., Bird, R. K., & Wallace, T. A. (1998). Titanium alloys and processing for high speed aircraft. Materials Science and Engineering A, 243(1-2), 299-304. https://doi.org/10.1016/ s0921-5093(97)00818-6

Chen, J. C., & Pan, C. X. (2011).Welding of Ti-6Al-4V alloy using dynamically controlled plasma arc welding process.Transactions of Nonferrous Metals Society of China (English Edition), 21(7), 1506–1512. https://doi.org/10.1016/S1003-63 26(11)60888-1

Deshpande, A. A., Short, A. B., Sun, W., McCartney, D. G., Xu, L., & Hyde, T. H. (2012). Finite element-based analysis of experimentally identified parametric envelopes for stable keyhole plasma arc welding of a titanium alloy.Journal of Strain Analysis for Engineering Design, 47(5), 266–275. https://doi.org/10.1177/0309 324712445417

Kumar, P., & Sinha, A. N. (2019). Effect of heat input in pulsed Nd: YAG laser welding of titanium alloy (Ti6Al4V) on microstructure and mechanical properties. Welding in the World, 63(3), 673-689. https://doi.org/10.1007/s401 94-018-00694-w

Leonov, V. P., Mikhailov, V. I., Sakharov, I. Y., &Kuznetsov, S. V. (2016).Welding of high-strength titanium alloys of large thicknesses for use in marine environments.Inorganic Materials: Applied Research, 7(6), 877-883. https://doi. org/10.1134/S2075113316060083

Leyens, C. (2005). Oxidation and Protection of Titanium Alloys and Titanium Aluminides.Titanium and Titanium Alloys, 187-230. https:// doi.org/10.1002/3527602119.ch6

Lukoyanov, A. V. (2014). Formation of pores in the weld metal in automatic argon-shielded arc welding of titanium alloys. Welding International, 28(4), 301-303. https://doi.org/1 0.1080/09507116.2013.796682

Murav’ev, V. I., Krupskii, R. F., Fizulakov, R. A., &Demyshev, P. G. (2008).Effect of the quality of filler wire on the formation of pores in welding of titanium alloys.Welding International, 22(12), 853-858.

Muth, T. R., Yamamoto, Y., Frederick, D. A., Contescu, C. I., Chen, W., Lim, Y. C., Peter, W. H., & Feng, Z. (2013). Causal factors of weld porosity in gas tungsten arc welding of powder-metallurgy-produced titanium alloys.JOM, 65(5), 643–651. https://doi.org/10.1007/s11837-013-0592-5

Pantelis, D. I., Kazasidis, M., &Karakizis, P. N. (2017). Titanium Alloys Thin Sheet Welding with the Use of Concentrated Solar Energy. Journal of Materials Engineering and Performance, 26(12), 5760–5768. https://doi.org/10.1007/ s11665-017-3049-0

Peters, M., Hemptenmacher, J., Kumpfert, J., &Leyens, C. (2005).Structure and Properties of Titanium and Titanium Alloys.In Titanium and Titanium Alloys, 1-36.

Peters, M., Kumpfert, J., Ward, C. H., &Leyens, C. (2003). Titanium alloys for aerospace applications. Advanced Engineering Materials, 5(6), 419–427. https://doi.org/10.1002/adem. 200310095

Short, A. B. (2009). Gas tungsten arc welding of α + β titanium alloys: A review. Materials Science and Technology, 25(3), 309-324. https://doi. org/10.1179/174328408X389463

Sibum, H. (2003). Titanium and titanium alloys - From raw material to semi-finished products. Advanced Engineering Materials, 5(6). https:// doi.org/10.1002/adem.200310092

Sun, W., Mohammed, M. B., Xu, L., Hyde, T. H., McCartney, D. G., &Leen, S. B. (2014). Process modelling and optimization of keyhole plasma arc welding of thin Ti-6Al-4V. Journal of Strain Analysis for Engineering Design, 49(6), 410-420. https://doi.org/10.1177/0309324714524947

Sundaresan, S., & Janaki Ram, G. D. (1999).Use of magnetic arc oscillation for grain refinement of gas tungsten arc welds in α-β titanium alloys.Science and Technology of Welding and Joining, 4(3), 151–160. https://doi. org/10.1179/136217199101537699

Vasechkin, M. A., Davydov, O. Y., Kolomenskii, A. B., &Egorov, S. V. (2018). Effect of Welding and Heat Treatment Regimes on the Mechanical Properties of Various Titanium Alloy Welded Joints. Chemical and Petroleum Engineering, 54(7-8), 525–530. https://doi.org/10.1007/ s10556-018-0512-1

Vyskoč, M., Sahul, M., & Sahul, M. (2018).Effect of Shielding Gas on the Properties of AW 5083 Aluminum Alloy Laser Weld Joints.Journal of Materials Engineering and Performance, 27(6), 2993–3006. https://doi.org/10.1007/s11665- 018-3383-x

Downloads

Published

01-05-2022

How to Cite

Pragatheswaran, T., Rajakumar, S., & Balasubramanian, V. (2022). Role of plasma gas flow rate on the microstructural and mechanical aspects of plasma arc welded titanium alloy joints. Manufacturing Technology Today, 21(5-6), 15–22. Retrieved from https://mtt.cmti.res.in/index.php/journal/article/view/32

Issue

Vol. 21 No. 5-6 (2022): May-June 2022

Section

Articles

License

All the articles published in Manufacturing Technology Today (MTT) Journal are held by the Publisher. Central Manufacturing Technology Institute (CMTI) as a publisher requires its authors to transfer the copyright prior to publication. This will permit CMTI to reproduce, publish, distribute, and archive the article in print and electronic form and also to defend against any improper use of the article.

Most read articles by the same author(s)